- M1145033.00
- M1135042.00
- M1135044.00
- M1135297.00
- 107013.00
- M1135110.00
- M1135045.00
- M1145032.00
- M1135107.00
- M1125074.00
- 096014.00
- M1135246.00
- M1125214.00
- M1135108.00
- M1125006.00
- M1135116.00
- M1135043.00
- M1125073.00
- M1135069.00
- M1135111.00
- M1125070.00
- M1125071.00
- 096013.00
- 108709.00
- 108712.00
- M1125219.00
- M1135114.00
- M1115000.00
- 107032.00
- M1135046.00
AC Gearmotors Parallel Shaft
AC Gearmotors
General Specifications - SCR Rated Gearmotors:
- Performance matched for continuous duty service over 60:1 speed range
- Constant torque throughout the range when powered by a full-wave unfiltered SCR-type adjustable speed control having a typical form factor of 1.3 to 1.4
General Specifications - LowVoltage Gearmotors:
- Performance matched for continuous duty service
- Designed for battery power or can be used with a low voltage controller with form factor up to 1.05
Features:
- Worm-type right-angle gearing features hardened, steel worm with bronze worm wheel for long life and quiet operation
- Precision machined aluminum gear housing
- Lubrication is permanent with an oil bath
- Gearbox has all ball bearings
- Output shaft is field interchangeable from left hand to right hand style by reassembly
- Double output shaft available as a factory option
- Optional conduit box available
- Optional gearbox base available (10 Series only)
Application Notes:
- Placing the gearmotor with the motor below the gearbox should be avoided to prevent leakage of lubricant into the motor should the motor shaft seal fail
- These right-angle gearmotors have a lubrication breather positioned for horizontal mounting. For other mountings, the breather plug must be reoriented by using a 90° 1⁄8" NPT taper pipe elbow. Regal does not offer this elbow. It is not recommended to place the gearmotor with the gearbox shaft up.
- Overhung load capacities shown are at center of output shaft
Parallel Shaft - SUB-FHP - AC Gearmotors
12-100 In-Lbs. Output Torque
Features:
- Permanent split capacitor design rated for 115 VAC 60 HZ input
- Precision machined in-line steel gears
- First stage steel helical gear followed by spur-type gears
- Lubrication is permanent semi-fluid grease, reducing possibility of leakage
- Output shafts have needle bearings for high load capacities
- Shafts are hardened steel
- Optional conduit box and PZ gearmotor mounting bracket available
Application Notes:
- Placing the gearmotor with the motor below the gearbox should be avoided to prevent leakage of lubricant into the motor should the motor shaft seal fail
- The motor’s stall torque could exceed recommended full load torques causing gearhead damage, especially in ratios of 60:1 and higher. Provisions to limit the torque are recommended
- The torque values listed are the recommended full load torque values
- Overhung load capacities shown are at center of output shaft
- All PZ Series gearmotors are supplied with continuous duty “run” capacitor
- Optional conduit box available
- Bodine/Bison/Dayton direct interchange
P240 Series - SUB-FHP - AC Gearmotors
Output Torque - 43-391 In-Lbs.
Features:
- Permanent split capacitor design rated for 115/230 VAC 60/50 HZ input
- Precision machined in-line steel gears
- First stage steel helical gear followed by spur-type gears
- Lubrication is permanent semi-fluid grease, reducing possibility of leakage
- Output shafts have needle bearings for high load capacities
- Shafts are hardened steel
- Optional conduit box available
Application Notes:
- Placing the gearmotor with the motor below the gearbox should be avoided to prevent leakage of lubricant into the motor should the motor shaft seal fail
- The motor’s stall torque could exceed recommended full load torques causing gearhead damage, especially in ratios of 60:1 and higher. Provisions to limit the torque are recommended
- Overhung load capacities shown are at center of output shaft
- All P240 Series gearmotors are supplied with continuous duty “run” capacitor
- Bison/Dayton direct interchange
PE350 Series - Parallel Shaft - AC Gearmotors
Output Torque - 25-341 In-Lbs
Features:
- All rated for 60/50 Hz operation except hi-torque single-phase which are 60 Hz only
- Rugged die cast aluminum gear housing for maximum gear and bearing support
- Precision machined gearing, hardened for maximum load capability
- All gearing designed and rated to AGMA class 9 standards, and to withstand momentary shock overload of 200%
- Oversized output bearings for greater overhung load capacity and long life
- High carbon alloy output shaft provides maximum strength and rigidity
- All needle bearing journals are precision ground after heat treating to provide maximum fit and finish
- Heavy duty industrial oil seals keep lubricant in and dirt out
- Gears and bearings are splash lubricated with permanent, heavy duty gear oil
- Run capacitor supplied at no additional cost for single phase designs
- Three phase and hi-torque single phase models include conduit box, other single phase models do not
- Placing the gearmotor with the motor below the gearbox should be avoided to prevent leakage of lubricant into the motor should the motor shaft seal fail
- Overhung load capacities shown are at center of output shaft
- Optional conduit box available
- Bodine/Baldor/Boehm direct interchange
PE350 Series - Parallel Shaft - AC Gearmotors
Output Torque - 25-341 In-Lbs
Features:
- All rated for 60/50 Hz operation except hi-torque single-phase which are 60 Hz only
- Rugged die cast aluminum gear housing for maximum gear and bearing support
- Precision machined gearing, hardened for maximum load capability
- All gearing designed and rated to AGMA class 9 standards, and to withstand momentary shock overload of 200%
- Oversized output bearings for greater overhung load capacity and long life
- High carbon alloy output shaft provides maximum strength and rigidity
- All needle bearing journals are precision ground after heat treating to provide maximum fit and finish
- Heavy duty industrial oil seals keep lubricant in and dirt out
- Gears and bearings are splash lubricated with permanent, heavy duty gear oil
- Run capacitor supplied at no additional cost for single phase designs
- Three phase and hi-torque single phase models include conduit box, other single phase models do not
- Placing the gearmotor with the motor below the gearbox should be avoided to prevent leakage of lubricant into the motor should the motor shaft seal fail
- Overhung load capacities shown are at center of output shaft
- Optional conduit box available
- Bodine/Baldor/Boehm direct interchange
P1100 Series - AC Gearmotors - Parallel Shaft
Output Torque - 70-1105 In-Lbs
Features:
- Capacitor start designs rated for 115/230 VAC 60 HZ input
- Rugged die cast aluminum gear housing for maximum gear and bearing support
- Precision machined gearing, hardened for maximum load capability
- All gearing designed and rated to AGMA class 9 standards, and to withstand momentary shock overload of 200%
- Oversized output bearings for greater overhung load capacity and long life
- High carbon alloy output shaft provides maximum strength and rigidity
- All needle bearing journals are precision ground after heat treating to provide maximum fit and finish
- Heavy duty industrial oil seals keep lubricant in and dirt out
- Gears and bearings are splash lubricated with permanent, heavy duty gear oil
- Conduit box included as standard
Application Notes:
- Placing the gearmotor with the motor below the gearbox should be avoided to prevent leakage of lubricant into the motor should the motor shaft seal fail
- Overhung load capacities shown are at center of output shaft
- Bison/Dayton direct interchange
Associated Models